[email protected]

Fatigue Performance of Thermally Cut Bolt Holes in

The material chosen for this research is structural steel S460M, supplied in rolled plates of 2000 mm x 2500 mm and 15 mm thickness. The selection criterion of this steel grade and thickness is its use in heavy loaded parts of bridges, in the building sector, yellow goods and manufacturing industry. The S460M steel is a thermomechanical MATERIAL DATA SHEETS FOR STRUCTURAL STEELTable 1:Material Data Sheets for Structural Steel NORSOK Steel Grade Standard Product Type Steel Quality Level MDS number S 235 JR G2 EN 10 025 Plates, Sections and Seamless tubulars IV Y01 S 275 JR EN 10 025 Plates, Sections and Seamless tubulars IV Y02 S 355 J2 G3NO 1 EN 10 025prEN 10225 Plates, Sections and Seamless

NEW GENERATION X-BT DATA SHEET - Hilti

Performance data Construction steel Conditions for recommended loads: Application of working load design concept (e.g. ASD) For unalloyed construction, off-shore and Shipbuilding steel:e.g. European grades S235, S275, S355 according to EN 10025-2, S355M, S420M, S460M according to EN 10025-4 or EN 10225, S690Q and S960Q Plates - Vítkovice SteelVÍTKOVICE STEEL, a.s. is a leading European manufacturer of rolled steel products. Its main product mix consists of heavy plate, sheet piles, sections and flame-cut shapes. Plates are rolled on four-high rolling mill from continuously cast slabs. Promat Durasteel Product Data SheetDURASTEEL® Technical data Thickness mm 6 9.5 Building material class DIN 4102 A1, non-combustible A1, non-combustible Classification temperature Permanent stress Short term up to ºC ºC 400 1000 400 1000 Bulk density kg/m3 2800 2210 Cold compressive strength N/mm2 60 60 Bending strength N/mm2 109 84 Tensile strength N/mm2 32 30 Modulus of elasticity E N/mm2 55000 40000

S460M in BSEN10113/3-93 standard - EQUIMETALS

S460M is a(n) british steel defined in BSEN10113/3-93 standard. (Looking for this designation of material quality, but standard does not match? Click here!) SSAB Domex 460MC - meets S460MC - SSABSSAB Domex® 460MC is a hot-rolled, high-strength low-alloy (HSLA) steel that features consistent quality and excellent engineering properties. SSAB Domex 460 MC meets or exceeds the requirements of S460MC in EN 10149-2 SSAB high-strength steel - sheet, plate, coil, tube SSAB, Swedish steel manufacturer of high-strength wear and structural steel. Hot and cold rolled, sheets, plates and coils, steel tubes and profiles, steel piles and more.

Steel Grade Equivalency Table

Steel Grade Equivalency. A633 Gr. A,C,D. 0.9 max. Comparative designations of grades with similar composition from other important standards. Unified Numbering System (UNS) is an alloy designation system widely accepted in North America. American Iron and Steel Institute (AISI) standards for steel compositions. European standards. Technical Data SheetTechnical Data Sheet ATI 500-MIL® Typical mechanical property data for ATI 500MIL-® specialty steel is included below. This data represents an average of results for 0.275 in. (7 mm) and 0.199 in. (5 mm) plate. HARDNESS . Steel will re-harden in the 477 to 534 BHN range. ThyssenKrupp XABO® 460 Structural SteelS460M; EN 1.8827, This Material Specification applies to thermo mechanically rolled flat products in thicknesses up to 60 mm. The criteria to distinguish the steel grades is the lowest test temperature for the notch-bar impact test. Application:

High-strength S460M sections from British Steel deliver

S460M steel grade The tables below indicate the standard mechanical properties and chemical composition for the S460M steel grade. Mechanical properties 1. Tensile test Specification Grade Minimum yield strength (MPa) Tensile strength Rm (MPa) Minimum elongation - A Nominal thickness (mm) Nominal thickness (mm) Lo = 5,65 So (%) 16 >16