[email protected]

AISI D2 Cold Work Tool Steel Data Sheet

blanking of parts in thin sheets. Hardness, HRC 70 68 66 64 62 60 58 56 54 52 50 Grain size Retained austenite Grain size ASTM 10 9 8 7 6 5 4 3 2 1 Hardness HRC 65 60 55 50 45 40 35 30 Retained austenite % 18 14 10 8 1920°F Cutting data speed steel parameters Rough turning Fine turning Fine turning coated carbide grade, for example ATI 321/ATI 347/ATI 348High carbon versions of all three alloys are available. These grades have UNS designations S32109, S34709, and S34809. PRODUCT FORMS ATI 321, ATI 347 and ATI 348 stainless steel is available in plate, sheet, and strip forms from ATI. CORROSION RESISTANCE. General Corrosion

Download Center - SSAB - SSAB high-strength steel - sheet

Jun 01, 2021 · SSAB, Swedish steel manufacturer of high-strength wear and structural steel. Hot and cold rolled, sheets, plates and coils, steel tubes and profiles, steel piles and more. Drawing and Forming Steel GradesGrade C max Mn max P max S max KHR1 1 0,08 0,45 0,025 0,030 HR2 2 0,08 0,54 0,030 0,035 HR3 2 0,10 0,50 0,040 0,040 HR4 2 0,12 0,60 0,050 0,050 Data Sheet:A4.1 Drawing and Forming Steel Grades Hot rolled formable steel coil FM Global Loss Prevention Data Sheets FM GlobalFM Global conducts research for use in the data sheets that our engineering field staff use to support our clients efforts to protect their business. The research is also used to enhance external standards and codes. This section contains reports that are generated to

GALVANIZED STEEL Grade Data Sheet - Cascadia

GRADE 37 Mechanical Properties Chemical Composition Steel base Guaranteed Typical Range Guaranteed Maximum Percent Longitudinal tensile Carbon (C) 0.20 Yield strength, minimum ksi 37 37-54 Phosphorus (P) 0.10 Tensile strength, minimum ksi 52 52-69 Manganese (Mn) 1.35 Industeel SUPERELSO® 690CR Quenched and Tempered DNV NVF 690/grade F, ASTM A514-A517, Superelso® 690 CR (SE 690 CR) is a 690MPa (100ksi) yield strength quenched and tempered steel adapted for jack-up rig legs of offshore drilling platforms. Superelso® 690 CR is manufactured via the electric MATERIAL DATA SHEETS FOR STRUCTURAL STEELThe grades 235 and 275 (MDS Y01 and Y02) shall not be used for thicknesses above 25 mm. 5.2 Selection Criteria The number of steel grades used in a project should be limited to the practical minimum (preferably one). An evaluation should be carried out to determined the optimum grade. Table 1:Material Data Sheets for Structural Steel NORSOK

MetalsDepot® - A514 Plate T1 Steel Plate - Buy Online!

A514 Steel Plate aka T1 steel plate is a high strength steel plate designed for applications requiring optimal impact and abrasive resistance. A514 T1 steel plate provides a high yield strength of 100 ksi min. with good weldability and toughness. Designed for a wide range of structural uses, as well as for machinery and equipment, A514 T1 Steel Plate offers optimum in strength, toughness Stainless Steel Grade DatasheetsGrade Data Sheet 301 301L 301LN Revised May 2008 Page 1 of 2 atlassteels.au Grade 301 is a high work-hardening rate austenitic stainless steel. It can be supplied with a tensile strength of up to over 1300 MPa in strip and wire forms, to produce tempers in the range of 1/16 Hard to Full Hard. The controlled analysis of Grade 301 enables Standard Specication for Forged or Rolled Alloy-Steel remelting. Grade F XM-27Cb may be produced by electron-beam melting. Because of difficulties that may be met in retaining nitrogen, vacuum melting or remelting processes should not be specied for Grades F XM-11, F 304LN, F 316LN, F 304N, F 316N, F XM-19, F 44, F 45, F 48, F 49, F 50, F 51, F 52, F 53, F 54, F 55, F 58, F 59, or F 60.

Welding Procedure Guide - MTEC

4.0 Welding Procedure Data Sheet (WPDS) A welding procedure data sheet (WPDS) is a document, used in conjunction with a WPS, detailing the welding parameters and ranges for welding a specific joint, over a range of thicknesses and weld sizes, as illustrated on the data sheet. The following is the standard welding procedure data sheet form ASTM A517 Grade F Quenched and Tempered - Low Carbon A Low Carbon Steel also known as DIN 1.0529 ,JIS SGC490 ,ISO 350 ,ASTM HSLAS Grade 340 Class 1with Tensile strength = 795.0MPa. Datasheet Download.