[email protected]

ASTM A623M-09 - Standard Specification for Tin Mill

Standard Specification for Tin Mill Products, General Requirements [Metric] 1.1 This specification covers a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to tin mill products. ASTM-A623 Standard Specification for Tin Mill Products This specification covers a group of common requirements which shall apply to tin mill products. The steel shall be made by the open-hearth, electric-furnace, or basic-oxygen process. The steel shall conform to specified chemical composition requirements. Rockwell 30T hardness test shall be done to

ASTM-A623M Standard Specification for Tin Mill Products

ASTM-A623M Standard Specification for Tin Mill Products, General Requirements [Metric] - ICS Number Code 77.140.50 (Flat steel products and semi-products) Aluminum Extrusion Dimensions and Tolerances Industry Standards for Extrusions are published in National Standard Dimensional Tolerances for Aluminum Mill Products (ANSI H35.2) and Aluminum Standards and Data (ASD). These standards feature specific dimensions and tolerances as well as formulas published in table format. Guide to TinplateCoils for tinplate usage usually have a final gauge somewhere between 1.6mm - 3.0mm. The roughing section may comprise four or five four-high non-reversing stands or a single four-high reversing mill, dependent on the mill design. The finishing train may have

IS 1852 (1985):Rolling and cutting tolerances for hot

IS :1852 - 1985 Indian Standard SPECIFICATION FOR ROLLING AND CUTTING TOLERANCES FOR HOT-ROLLED STEEL PRODUCTS ( Fourth Revision ) Second Reprint AUGUST 1993 UDC 66914-423-1224 i 6217531 0 Copyrighr 1986 BUREAU OF INDIAN STANDARDS Plating System Specifications and Inspection Techniques3.2 Specifications, Standards and Directives. ASTM International ASTM B488 Standard Specification for Electrodeposited Coatings of Gold for Engineering Uses ASTM B545 Standard Specification for Electrodeposited Coatings of Tin ASTM B567 Standard Test Method for Measurement of Coating Thickness by Beta Backscatter Method Standard Details for Metal Roofing & SidingStandard Details for Metal Roofing & Siding Post Frame and Residential Structures Distributed by:BEST MATERIALS ® Ph:800-474-7570, 602-272-8128 Fax:602-272-8014 BestMaterials Email:[email protected]

Standard Specification for Tin Mill Products, General

A623M - 02a Standard Specification for Tin Mill Products, General Requirements [Metric] , Modul-R, R-bar, TIN MILL PRODUCTSDesignation of Standard Tin Coating Mass (g/m2) Equally Coated 2.8 5.6 8.4 11.2 Diffrentially Coated 2.8/5.6 2.8/8.4 2.8/11.2 5.6/8.4 5.6/11.2 8.4/11.2 The tin coating mass is changed depending on usage. In case of heavier tin coating mass, it is applied to high Tin Mill Products Berlin MetalsSheet and tin mill products are differentiated by gauge. Electrolytic tinplate has a maximum thickness of 135 lb. base weight or 0.0149 inch nominal thickness. Tin coated sheet starts at 0.0150 inch nominal thickness and is produced up to 0.0359 inch nominal thickness. Use of Chromium Coating

Tinplate ::ArcelorMittal Dofasco

Standard Coating Weights Tinplate coating weights may be eed in the traditional units of lb/ base box or in SI units of g/m 2. ArcelorMittal Dofasco can supply a full range of coatings from #5 (.5 g/m 2) to #100 (11.2 g/m 2). Differential coatings are also available.Standard Specification for Tin Mill Products, General This specification covers a group of common requirements which shall apply to tin mill products. The steel shall be made by the open-hearth, electric-furnace, or basic-oxygen process. The steel shall conform to specified chemical composition requirements. Rockwell 30T hardness test shall be done to